Diode-led OMNIDRIVE Bedienungsanleitung PDF herunterladen

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

1 OF 4

OMNIDRIVE™ ELECTRONIC DIMMABLE DRIVER

IG071014-1.1

Safety & Warnings

• Install in accordance with the Naonal Electric Code, and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• Only install compable LED xtures & controls. Only use copper wiring.

• Proper heat dissipaon will prolong the working lifespan of this product.

Install in a well-venlated area free from explosive gases and vapors.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overheat wires, and cause a re.

• Do not install if product has any visible damage.

• Do not modify or disassemble this product beyond instrucons or the

warranty will be void.

Prior to installaon, ensure all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure

all components are operang correctly. Install in accordance with the NEC and local regulaons.

WARNING

Shock Hazard. May result in serious injury or death.

Installation

Turn OFF High Voltage AC Power at the main breaker.

OFFOFFOFF

ONON

OFFOFF

ONON

Determine Locaons to Install 3 Main Components.

Refer to the ‘System Diagrams.’

V+

V-

Ensure applicable wire is installed between driver, xture, and any controls

in between. When choosing wire, factor in voltage drop, amperage rang,

and type (in-wall rated, wet locaon rated, etc.).

1) Compable

Control

2) Driver 3) Fixture

Aach Lighng Load and Control (min load of 60% labeled

load for dimmable installaons). Only use copper wiring.

Refer to ‘Wiring Connecons’, ‘System Diagrams’, and dimming

control installaon guides. Ensure to install a compable

dimming control listed on the ‘OMNIDRIVE / Dimming Control

Compability List’ available at www.DiodeLED.com.

-22 32 50 68 86 104 140 158

100

Ambient Temperature (°F)

122

Load (%)

a. When installing in ambient temperatures that may reach over

100°F, refer to the ‘Derang Curve’ to avoid overheang and

damage to the driver.

Mount Driver to Surface. See ‘Wiring Connecons’ for mounng

holes. Driver may be mounted in any orientaon. Mounng

screws are included with 10W, 20W, and 30W models.

DERATING CURVE

Quick Specs

Input Voltage 90~135VAC, 50/60Hz

Output Voltage See driver label

Ambient Temperature † -40°F ~ 140°F (-40°C ~ 60°C)

Minimum Load ≥ 60% (for dimmable installaons)

Maximum Load Refer to ‘Derang Curve’

Included Models

Indoor/Dry Locaon Models Outdoor/Wet Locaon Models

TD-**V-10W TD-**V-60W

TD-**V-20W TD-**V-80W

TD-**V-30W

TD-**V-45W

† Do not install product in an environment outside the listed ambient

temperature.

** Indicates voltage output (12V or 24V).

Before you begin, read all warnings and installaon instrucons thoroughly.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - 1.877.817.6028

[email protected] www.DiodeLED.comINSTALLATION GUIDE1 OF 4®OMNIDRIVE™ ELECTRONIC DIMMABLE DRIVERIG071014-1.1Safety &

Seite 2 - INCORRECT

[email protected] www.DiodeLED.comINSTALLATION GUIDE2 OF 4®OMNIDRIVE™ ELECTRONIC DIMMABLE DRIVERIG071014-1.1b. Indoor/

Seite 3 - System Diagrams

[email protected] www.DiodeLED.comINSTALLATION GUIDE3 OF 4®OMNIDRIVE™ ELECTRONIC DIMMABLE DRIVERIG071014-1.1AC Power50/

Seite 4 - QUESTIONS?

[email protected] www.DiodeLED.comINSTALLATION GUIDE4 OF 4®OMNIDRIVE™ ELECTRONIC DIMMABLE DRIVERIG071014-1.1Additional

Kommentare zu diesen Handbüchern

Keine Kommentare

Diode-led OMNIDRIVE Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Diode-led OMNIDRIVE herunter. Diode LED OMNIDRIVE User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Diode-led OMNIDRIVE