1 of 4
INSTALLATION GUIDE
RGBW ZONE COLOR CONTROLLER
IG022614-1.0
Safety & Warnings
Before you begin, read all warnings and installaon instrucons thoroughly.
Prior to installaon, verify all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure all
components are operang correctly. Install in accordance with the NEC and local regulaons.
1. Turn OFF 120~277VAC power at circuit breaker prior to installaon.
2. Remove the Input and Output cover ports of the zone receiver with a
#2 Phillips head screwdriver. Connect a compable constant voltage DC
driver to the receiver. See ‘Wiring Connecons’ and the ‘System Diagram.’
3. Connect a compable RGBW xture to the receiver. Ensure not to
overload the receiver. In addion, do not exceed the maximum run
length of the xture. See ‘System Diagram.’
4. Install addional components and accessories. Once complete, turn
circuit breaker ON.
• Install in accordance with the Naonal Electric Code, and local regulaons.
• This product is intended to be installed and serviced by a qualied,
licensed electrician.
• Do not connect directly to high voltage 120V~277V power. Install with a
compable Class 2 constant voltage LED driver (power supply).
• Only install compable LED drivers and xtures. Contact technical support
or visit the product page for compable products.
• This product is rated for indoor installaon and is not protected against
moisture.
• Proper heat dissipaon will prolong the working lifespan of this product.
Install in a well-venlated area free from explosive gases and vapors.
• Ensure applicable wire is installed between driver, xture, and any controls
in between. When choosing wire, factor in voltage drop, amperage
rang, and type (in-wall rated, wet locaon rated, etc.). Inadequate wire
installaon could overhead wires, and cause a re.
• Do not modify or disassemble this product beyond instrucons or the
warranty will be void.
Input Voltage 5VDC Built-in Lithium Baery
Transming Distance 99 .
Control Type
Pulse Width Modulaon (PWM). 4-channel
RGBW xtures.
Ambient Temperature † -4° ~ 131°F (-20° ~ 55°C)
Input / Output Voltage 5-24VDC constant voltage
Max Current Load 5A x 4CH Max 20A
Max Output Power
100W/240W/480W (5V/12V/24V)
Ambient Temperature
-22° ~ 131°F (-30° ~ 55°C)
Environment Indoor / dry locaon
RGBW Zone Remote
RGBW Zone Receiver
For full specicaons, see the ‘Specicaon Sheet’ available at the online
product page.
• A ashing red indicator light on the zone remote implies a low baery.
• To charge the remote, connect the included USB 2.0A/Mini-B cable to the
remote and to a 5VDC USB port.
• Press the power buon on the remote and a blue indicator light will ash
to indicate charging. Once the indicator light turns green, charging is
complete.
• Turn on the remote and the receiver.
• Long press the ‘Learning ID’ buon on the receiver unl the receiver
beeps. Immediately long press a desired zone on the remote.
• To indicate pairing, the receiver will long beep and a green indicator will
ash 3 mes on the remote.
Do not pair mulple remotes to a single receiver or pair mulple receivers to
a single zone. Doing so will cause the system to funcon improperly. Reset
the remote and receiver to factory sengs if improper pairing is performed.
Charging the Remote
Pairing the Remote with a Receiver
Reseng Remote & Receiver to Factory Sengs
• To reset the remote, turn on remote and hold Power for three seconds. A
red indicator will ash red 3 mes and the remote will be reset.
• To reset a single receiver, long press the ‘Learning ID’ buon on the
receiver (you will hear an inial beep). Connue holding for >8 seconds
unl the receiver long beeps. The receiver has now been reset to factory
sengs.
Installing the Receiver
Installation
Quick Specs
See the online product page for video
tutorials or contact technical support.
Need Addional Assistance?
†
Do not install product in an environment outside the listed ambient
temperature. Ensure adequate airow and heatsinking is considered
when mounng/installing.
WARNING
Shock Hazard. May result in serious injury or death.
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern