1 of 2
INSTALLATION GUIDE
RGB INLINE COLOR CONTROLLER
IG022614-1.0
Safety & Warnings
Before you begin, read all warnings and installaon instrucons thoroughly.
Prior to installaon, verify all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure all
components are operang correctly. Install in accordance with the NEC and local regulaons.
1. Turn OFF 120~277VAC power at circuit breaker prior to installaon.
2. Remove the Input and Output cover ports of the receiver with a #2
Phillips head screwdriver. Connect a compable constant voltage DC
driver to the receiver. See ‘Wiring Connecons’.
3. Connect a compable RGB xture to the receiver. Ulize the V+, R, G,
B terminal ports for RGB xtures. See ‘Wiring Connecons’. Ensure not
to overload the receiver. In addion, do not exceed the maximum run
length of the xture.
4. Install addional components and accessories. Once complete, turn
circuit breaker ON.
• Install in accordance with the Naonal Electric Code, and local regulaons.
• This product is intended to be installed and serviced by a qualied,
licensed electrician.
• Do not connect directly to high voltage 120V~277V power. Install with a
compable Class 2 constant voltage LED driver (power supply).
• Only install compable LED drivers and xtures. Contact technical support
or visit the product page for compable products.
• This product is rated for indoor installaon and is not protected against
moisture.
• Proper heat dissipaon will prolong the working lifespan of this product.
Install in a well-venlated area free from explosive gases and vapors.
• Ensure applicable wire is installed between driver, xture, and any controls
in between. When choosing wire, factor in voltage drop, amperage
rang, and type (in-wall rated, wet locaon rated, etc.). Inadequate wire
installaon could overhead wires, and cause a re.
• Do not modify or disassemble this product beyond instrucons or the
warranty will be void.
RGB Remote
Receiver
Installation
Quick Specs
Input Voltage 3VDC Baery (CR2032)
Transming Distance 130 .
Control Type
Pulse Width Modulaon (PWM). 3-channel
RGB xtures.
Ambient Temperature † -4° ~ 122°F (-20° ~ 50°C)
Input / Output Voltage 12-24VDC constant voltage
Max Current Load 3A x 3CH Max 9A
Max Output Power
108W/216W (12V/24V)
Ambient Temperature
† -22° ~ 122°F (-30° ~ 50°C)
Environment Indoor / dry locaon
For full specicaons, see the ‘Specicaon Sheet’ available at the online
product page.
†
Do not install product in an environment outside the listed ambient
temperature. Ensure adequate airow and heatsinking is considered
when mounng/installing.
• Pull out baery tab of the remote and power up remote and receiver.
• Long press the Learning ID buon on the receiver for >5 seconds unl
the red running light blinks rapidly. Immediately release the ‘Learning ID’
and short press it again.
• Now press a buon on the remote to send a signal and the remote will
sync to the receiver. Aer 3 seconds the running light on the receiver
should blink at a normal rate (roughly 1 blink per second).
If installing mulple controllers and receivers, do not pair mulple remotes
to a single receiver. Each remote must be paired to a single receiver or the
system will funcon improperly. Reset the receiver to factory sengs if
improper pairing is performed.
Pairing the Remote and ReceiverInstalling the Receiver
Reseng the Receiver to Factory Sengs
• To reset the receiver, long press the Learning ID buon on the receiver
for >10 seconds.
• During this period the running light will ash rapidly for <5 seconds. You
can release the ‘Learning ID’ once the rapid ashing slows to a normal
rate (roughly 1 blink per second).
• The receiver has now been reset to factory sengs.
Reseng the Receiver to Factory Sengs
See the online product page for video
tutorials or contact technical support.
Need Addional Assistance?
WARNING
Shock Hazard. May result in serious injury or death.
Kommentare zu diesen Handbüchern